Author Topic: Clutch setting  (Read 2612 times)

0 Members and 1 Guest are viewing this topic.

Offline dcX

  • Trade Count: (0)
  • Registered Bridgestone Member
  • **
  • Posts: 8
Clutch setting
« on: March 18, 2024, 04:43:24 AM »
Hi All,
Please can someone share the correct clutch setting, what is the correct position for the 6 off M5 x 12 screws (that hold the set plate down):-
1. how far should these be screwed in & where is the measured from?
2. what prevents the screws unwinding as its not practical (that I can see) to balance the pressure on the set plate across all 6 screws, (a tab washer would prevent unwinding but there's nothing shown, similarly thread lock would work but would impede dis-assembly)?

Thanks
Dave

Offline OldSwartout

  • Global Moderator
  • Trade Count: (0)
  • *******
  • Posts: 1316
Re: Clutch setting
« Reply #1 on: March 18, 2024, 09:15:52 AM »
Those screws are tightened all the way until the set plate is against the posts on the pressure plate sticking through from the back side. I didn't see a torque value anywhere, but just nice and snug is my guide. Remember, they're only 5mm. I usually screw them in a few turns at a time working around the pattern to keep from overloading any single one as they're pulled down. I'm not sure it that has any value or not.
Karl Swartout
Mooresville, IN
BS175 Roadracer. BS200RS, BS350 GTR

Offline BRT-GTR

  • Brian
  • Trade Count: (0)
  • Master Registered Bridgestone Member
  • *****
  • Posts: 951
Re: Clutch setting
« Reply #2 on: March 18, 2024, 11:36:38 AM »
   Re ;- Screw tightening - Agreed, it is good engineering practice to tighten any multiple screw, spring loaded assembly in stages. This avoids warpage and/or overloading of the assembly. It also applies to cylinder heads and crankcase screws, although these are not spring loaded.
     No screw locking device is required because the clutch springs acts a locking device, similar to those found on the adjusters on the carbs. I have never known a clutch screw come loose.
        Brian.
Unspoiled by progress.
I'm so glad I grew up in the 60s & 70s. I did so much stupid stuff and there's no record of it.............Anywhere !!

Offline dcX

  • Trade Count: (0)
  • Registered Bridgestone Member
  • **
  • Posts: 8
Re: Clutch setting
« Reply #3 on: March 21, 2024, 07:06:13 PM »
Thanks Karl & Brian
Hopefully I'll get chance to give it a go this weekend
Dave

 


Gallery


Views:692
Comments (0)
By: hod928

Views:694
Comments (0)
By: hod928

Views:671
Comments (0)
By: hod928

Views:843
Comments (0)
By: hod928

Classifieds

Deleted

Price: $0.00
Date: 08/09/2024 07:09 am
Time Left:
Deleted

Price: $0.00
Date: 06/12/2024 07:57 am
Time Left:
BS 175 DT Carburettors Mikuni VM 17 s

Price: 120.00 EUR
Date: 04/14/2024 09:55 am
Time Left:
BS175 DT 1966 Gas Tank

Price: 150.00 EUR
Date: 04/14/2024 09:37 am
Time Left:

Recent Downloads added

Parts Manual BS-7 Std & Deluxe with new style part numbers
Rating: (None)
Filesize: 5483.15KB
Date: April 17, 2024, 10:15:22 AM
Chibi, Chibi Deluxe, Tora Service Manual
Rating: (None)
Filesize: 20383.27KB
Date: May 01, 2023, 08:35:39 PM
Chibi_Tora_Parts_Manual
Rating: (None)
Filesize: 14301.44KB
Date: May 01, 2023, 08:25:53 PM
BS200 Mk II RS & MK II SS Exclusive Parts
Rating: (None)
Filesize: 358.29KB
Date: March 07, 2021, 07:30:10 PM

Powered by EzPortal