Author Topic: Special Tools Identification  (Read 1254 times)

0 Members and 1 Guest are viewing this topic.

Offline moonpup

  • Laidback Purist
  • Trade Count: (0)
  • Master Registered Bridgestone Member
  • *****
  • Posts: 2264
Special Tools Identification
« on: July 09, 2019, 03:01:28 PM »
I would appreciate any help y'all could provide in identifying the tools pictured below.

Would like the following information on each of them....
1) Part number.
2) Part name.
3) What size engine it's for.

*** not necessary to answer all 3 questions at once, if you can provide just one answer for a particular tool, that puts me that much closer to the info i need. ***

Thanks.....
« Last Edit: July 10, 2019, 10:59:00 AM by moonpup »
Confucius say... "Better to have Bridgestone than Kidneystone"

Offline Jeff Bar

  • Trade Count: (0)
  • Expert Registered Bridgestone Member
  • ****
  • Posts: 484
Re: Special Tools Identification
« Reply #1 on: July 10, 2019, 09:55:09 PM »
#6 is  a seal driver Jeff Bar

Offline moonpup

  • Laidback Purist
  • Trade Count: (0)
  • Master Registered Bridgestone Member
  • *****
  • Posts: 2264
Re: Special Tools Identification
« Reply #2 on: July 10, 2019, 10:29:14 PM »
This morning I posted this over on the Facebook site and these are the results gathered so far from the helpful members there..... (Note: I've since looked in a couple of the Parts Price List manuals I have and have found additional numbers and the actual tool description per Bridgestone and have made the changes to the list as needed. it does appear that all the tools aren't listed in those manuals as I found nothing for #'s 7 & 8, yet those are pictured in the BS50-90 Optional Parts list??? )

#1
A) 9328-3001
B) Clutch tool
C) BS7

#2
A) 9379-8010
B) Clutch tool
C) 175's

#3
A) 9374-5000
B) Sprocket stopper
c) 90/100's

#4
A) 9534-3100
B) Stop wrench
c) 50/60/90/100's

#5
A) 9376-5010
B) Piston pin puller
C) 90/100's ( should work on 175's )

#6
A) 9378-8010
B) Carb gage
C) 175's

#7
A)
B) Oil seal installer
C) 175's

#8
A)
B) TDC Dial Indicator mounting base.
C) 175
« Last Edit: July 08, 2021, 10:44:28 PM by moonpup »
Confucius say... "Better to have Bridgestone than Kidneystone"

Offline moonpup

  • Laidback Purist
  • Trade Count: (0)
  • Master Registered Bridgestone Member
  • *****
  • Posts: 2264
Re: Special Tools Identification
« Reply #3 on: July 23, 2019, 11:23:58 PM »
Here's one I forgot about. It's a small little thing.... about 1 & 3/4" long and is pictured with the 175 special tools in the previously mentioned Optional Parts List.. Any ideas what it is?
« Last Edit: July 23, 2019, 11:29:47 PM by moonpup »
Confucius say... "Better to have Bridgestone than Kidneystone"

Offline SR-175

  • Trade Count: (0)
  • Full Bridgestone Member
  • ***
  • Posts: 101
Re: Special Tools Identification
« Reply #4 on: July 24, 2019, 11:17:12 AM »
It's an extension shaft that screws into a dial indicator. There should be another piece that has the spark plug thread with a through hole / grub screw to lock the dial indicator into.

Offline moonpup

  • Laidback Purist
  • Trade Count: (0)
  • Master Registered Bridgestone Member
  • *****
  • Posts: 2264
Re: Special Tools Identification
« Reply #5 on: July 24, 2019, 12:44:43 PM »
So you think this is part of tool #8 above? There are no lines/hash marks or numbers anywhere on it (should there be?) and it would "swim" in the opening of tool #8. It's length is also smaller than #8. I don't see how the 2 would work together, unless some other piece is missing.

Confucius say... "Better to have Bridgestone than Kidneystone"

Offline al_pritchard

  • Trade Count: (0)
  • Full Bridgestone Member
  • ***
  • Posts: 111
Re: Special Tools Identification
« Reply #6 on: July 24, 2019, 03:08:32 PM »
I think the missing part of tool #8 is a dial indicator.

Tool #8 would screw into the spark plug hole in the head. Then a dial indicator would slide onto the large hole in part #8.

The bottom of the dial indicator has a wide tube running out the bottom, and a smaller shaft inside of it. It's that wider tube that inserts into tool #8, and is held in place with a set screw.

The shaft above would be screwed onto that smaller shaft of the dial indicator making it long enough to reach down to the top of the piston.




Click Picture To See Video



Al Pritchard
Highlands, NJ

BS175 Racer

Offline moonpup

  • Laidback Purist
  • Trade Count: (0)
  • Master Registered Bridgestone Member
  • *****
  • Posts: 2264
Re: Special Tools Identification
« Reply #7 on: July 24, 2019, 04:04:54 PM »
Thanks Al, so the dial indicator would have to be sourced elsewhere or did BS supply/sale any?
Confucius say... "Better to have Bridgestone than Kidneystone"

Offline moonpup

  • Laidback Purist
  • Trade Count: (0)
  • Master Registered Bridgestone Member
  • *****
  • Posts: 2264
Re: Special Tools Identification
« Reply #8 on: July 24, 2019, 04:28:55 PM »
Here's a vintage Yamaha set-up I found on eBay..... it all makes sense now. (Thanks Ray & Al!  banana )
Confucius say... "Better to have Bridgestone than Kidneystone"

 


Gallery


Views:219
Comments (0)
By: Jon West

Views:1360
Comments (0)
By: rwgibbon

Views:1690
Comments (0)
By: Perry L Anderson

Views:1755
Comments (0)
By: Perry L Anderson

Classifieds

Gto
Date: 03/02/2024 06:49 am
Time Left:
Looking for a BS90 used or new luggage Carrier assembly

Date: 02/01/2024 04:19 pm
Time Left:
Gto
Date: 10/19/2023 01:08 pm
Time Left:
Urgent - l/end roller bearing & piston pins needed
Date: 10/08/2023 03:25 am
Time Left:

Recent Downloads added

Chibi, Chibi Deluxe, Tora Service Manual
Rating: (None)
Filesize: 20383.27KB
Date: May 01, 2023, 08:35:39 PM
Chibi_Tora_Parts_Manual
Rating: (None)
Filesize: 14301.44KB
Date: May 01, 2023, 08:25:53 PM
BS200 Mk II RS & MK II SS Exclusive Parts
Rating: (None)
Filesize: 358.29KB
Date: March 07, 2021, 07:30:10 PM
1970 sales brochure
Rating: *****
Filesize: 6753.33KB
Date: July 16, 2020, 10:01:18 PM

Powered by EzPortal