Author Topic: Bridgestone 200 Oil injector pump  (Read 823 times)

0 Members and 1 Guest are viewing this topic.

Offline matthew_clayborne

  • Trade Count: (0)
  • Registered Bridgestone Member
  • **
  • Posts: 22
Bridgestone 200 Oil injector pump
« on: March 31, 2022, 01:15:08 PM »
Can someone show me what the circled bolt is supposed to look like, my pump does not have one. Its no listed in the parts list but I think it might be the plunger guide?
Resurrecting a 300$ 1969 Bridgestone 200 costs lots of money apparently.

Offline OldSwartout

  • Global Moderator
  • Trade Count: (0)
  • *******
  • Posts: 1312
Re: Bridgestone 200 Oil injector pump
« Reply #1 on: March 31, 2022, 08:53:06 PM »
I'm pretty sure that's what it is. I have some old 175 pumps around, can check tomorrow and send you one if needed. it would have been part of the pump assembly, not available as a spare.
Karl Swartout
Mooresville, IN
BS175 Roadracer. BS200RS, BS350 GTR

Offline matthew_clayborne

  • Trade Count: (0)
  • Registered Bridgestone Member
  • **
  • Posts: 22
Re: Bridgestone 200 Oil injector pump
« Reply #2 on: March 31, 2022, 11:10:40 PM »
That would be extremely helpful just let me know what you need for it if you have one to spare. Also is there a way to check these pumps? I have to order a gasket kit and don't want to ruin a good gasket on a bad pump.

Thank you for you help
Resurrecting a 300$ 1969 Bridgestone 200 costs lots of money apparently.

Offline OldSwartout

  • Global Moderator
  • Trade Count: (0)
  • *******
  • Posts: 1312
Re: Bridgestone 200 Oil injector pump
« Reply #3 on: April 01, 2022, 03:26:01 PM »
Out of 4 old pumps I have, 3 have a screw head bolt there, one is a 10mm hex head. Send me a message with your address and I'll just drop it in the mail.  These are obviously some kind of guide for the plunger as you thought. They also have a left hand thread.

As far as testing, hook an oil line supply to the center port. The supply should be above the pump, and bleed the air out of the line. Spin the shaft CCW (looking at the shaft) by hand, see if oil comes out the two other ports. You should hold the lever full open to see quickly if it is pumping. It pumps such a small amount per revolution, it will just ooze out. You could probably use a drill at about 1000 rpm to get quicker results once you have oil in the pump.
« Last Edit: April 01, 2022, 03:30:46 PM by OldSwartout »
Karl Swartout
Mooresville, IN
BS175 Roadracer. BS200RS, BS350 GTR

 


Gallery


Views:58
Comments (0)
By: Jon West

Views:1196
Comments (0)
By: rwgibbon

Views:1505
Comments (0)
By: Perry L Anderson

Views:1587
Comments (0)
By: Perry L Anderson

Classifieds

Looking for a BS90 used or new luggage Carrier assembly

Date: 02/01/2024 04:19 pm
Time Left:
Gto
Date: 10/19/2023 01:08 pm
Time Left:
Urgent - l/end roller bearing & piston pins needed
Date: 10/08/2023 03:25 am
Time Left:
197? Tora

Price: $2100.00
Date: 10/02/2023 10:24 am
Time Left:

Recent Downloads added

Chibi, Chibi Deluxe, Tora Service Manual
Rating: (None)
Filesize: 20383.27KB
Date: May 01, 2023, 08:35:39 PM
Chibi_Tora_Parts_Manual
Rating: (None)
Filesize: 14301.44KB
Date: May 01, 2023, 08:25:53 PM
BS200 Mk II RS & MK II SS Exclusive Parts
Rating: (None)
Filesize: 358.29KB
Date: March 07, 2021, 07:30:10 PM
1970 sales brochure
Rating: *****
Filesize: 6753.33KB
Date: July 16, 2020, 10:01:18 PM

Powered by EzPortal