Author Topic: Where does this 175 part go?  (Read 296 times)

0 Members and 1 Guest are viewing this topic.

Offline hgzumanity

  • Trade Count: (0)
  • Registered Bridgestone Member
  • **
  • Posts: 21
Where does this 175 part go?
« on: August 14, 2018, 06:31:11 PM »
Can anyone tell me where this piece goes?  It fell out when I took the clutch cover off. I have looked through the parts book and service manual and I don’t know where it came from. Thanks

Offline simonhk

  • Trade Count: (0)
  • New Member
  • *
  • Posts: 3
Re: Where does this 175 part go?
« Reply #1 on: August 14, 2018, 09:12:39 PM »
it goes in the outer  cover in the clutch actuating mechanism

Offline hgzumanity

  • Trade Count: (0)
  • Registered Bridgestone Member
  • **
  • Posts: 21
Re: Where does this 175 part go?
« Reply #2 on: August 14, 2018, 09:19:30 PM »
Thanks for the reply. I just looked at my clutch cover and that piece is still where it belongs. This metal dowel is quite a bit bigger than that one. Do you have any other ideas?

Offline bsforever

  • Trade Count: (0)
  • Full Bridgestone Member
  • ***
  • Posts: 162
Re: Where does this 175 part go?
« Reply #3 on: August 15, 2018, 12:12:34 AM »
I am not familiar with the 175's so any answer i guess at is just that.... a guess. Any possibilty it is a dowel pin that holds the cover onto the engine?  Might be too big for that , but just a shot-in-the-dark guess.

Offline al_pritchard

  • Trade Count: (0)
  • Full Bridgestone Member
  • ***
  • Posts: 88
Re: Where does this 175 part go?
« Reply #4 on: August 15, 2018, 09:48:35 AM »


Look in the lower right corner of the case in the image below. Could it be that pin? I think it’s the fork guide pin PN: 2113-8000. I haven’t seen any pin in the engine that big, other than that.

If thats the pin, for the life of me I can’t think of how it would migrate to the clutch side.

Al Pritchard
Highlands, NJ

BS175 Racer

Offline hgzumanity

  • Trade Count: (0)
  • Registered Bridgestone Member
  • **
  • Posts: 21
Re: Where does this 175 part go?
« Reply #5 on: August 15, 2018, 12:52:58 PM »
I believe you are right, Al. Thanks for the picture. My guess is it fell out into the bottom of the crank case and rolled through the hole at the bottom of the case between the gearbox and clutch area. I was hoping I wouldn't have to split the cases on this engine but maybe this is why the bike was parked in the first place. Thanks again

 


Gallery


Views:22
Comments (0)
By: harleywaynecycles

Views:20
Comments (0)
By: harleywaynecycles

Views:17
Comments (0)
By: harleywaynecycles

Views:9
Comments (0)
By: harleywaynecycles

Classifieds

BS Keychain (SOLD)

Price: $0.00
Date: 11/23/2018 12:51 pm
Time Left: 71d 20h 44m
350 engine carb covers left an right show quality SOLD!!!
Price: $0.00
Date: 11/18/2018 06:13 pm
Time Left: 67d 2h 7m
Frame etc Bridgestone 350

Price: $0.00
Date: 11/15/2018 11:52 pm
Time Left: 474d 7h 46m
[ebay] ‘67 175 DT - no reserve
Price: $0.00
Date: 11/09/2018 10:20 am
Time Left: 57d 18h 14m

Recent Downloads added

11/01/1967 Factory Service Letter, RH shift/LH Brake conversion

Rating: (None)
Filesize: 92.56KB
Date: August 03, 2018, 02:49:08 AM
11/01/1967 Factory Service Letter, RH shift/LH Brake conversion

Rating: (None)
Filesize: 142.24KB
Date: August 03, 2018, 02:44:36 AM
350 GTR Wiring Diagram
Rating: *****
Filesize: 8604.23KB
Date: July 29, 2018, 12:29:25 PM
Bridgestone Motorcycles

Rating: (None)
Filesize: 3561.91KB
Date: June 05, 2018, 04:42:13 PM

Powered by EzPortal