Author Topic: Replacement rectifier/regulator wiring  (Read 1278 times)

0 Members and 1 Guest are viewing this topic.

Offline BRT-GTR

  • Brian
  • Trade Count: (0)
  • Master Registered Bridgestone Member
  • *****
  • Posts: 783
Replacement rectifier/regulator wiring
« on: April 04, 2017, 03:38:21 PM »
   Hi all.
             Been looking for a low cost modern rectifier for some time but in one of those 'senior moments' I got carried away and ordered this :-

                http://www.ebay.co.uk/itm/191744045045?_trksid=p2055119.m1438.l2649&ssPageName=STRK%3AMEBIDX%3AIT

  It's bit bigger than I was expecting (4.25''  x 3.25'')with a massive double sided heat sink but should go under the seat or tank.   The one that came has slightly different wire colours to that advertised and looks very similar to the one below. Ok the 3 yellow wires connect to the alternator and the red and green wires go to the battery.  Can any of you elecrical experts tell me the best place to connect (or not connect) the sensing wire, which is black and smaller gauge than the others.  Seems similar to those fitted on some early Kawasaki and Yamaha models. It has 'YM1610' lightly marked on the case.
    Brian 
            PS. How do you insert photos in the text ?

           
« Last Edit: April 04, 2017, 03:48:33 PM by BRT-GTR »
Unspoiled by progress.

Offline OldSwartout

  • Global Moderator
  • Trade Count: (0)
  • *******
  • Posts: 1073
Re: Replacement rectifier/regulator wiring
« Reply #1 on: April 04, 2017, 05:42:30 PM »
Very nice and inexpensive.  I installed a similar regulator/rectifier from an early Kawasaki four.  One thing I just learned is that the regulator voltage sensing wire needs to hook up near the battery. I initially hooked it up to the switched power to the coils/lights (blue on the 350). The problem is that due to the small diameter wiring used on Bridgestones, there is .5 - 1.0 volt drop in the wiring, throwing off the voltage regulation.  I had a couple of oxidized connectors that added another .5 volt drop.  On the Kawasaki regulator, the voltage sensing wire did not need to be switched as there was no current draw to kill the battery during storage, so I hooked it directly to the battery positive lead.
Karl Swartout
Mooresville, IN
BS175 Roadracer
BS350 GTR

Offline BRT-GTR

  • Brian
  • Trade Count: (0)
  • Master Registered Bridgestone Member
  • *****
  • Posts: 783
Re: Replacement rectifier/regulator wiring
« Reply #2 on: April 07, 2017, 05:30:38 AM »
             Many thanks Karl. Exactly what I needed to know. I wasn't fully sure of the role of the sensing wire but now understand and where to fit the connection. Will carry out a current draw check test when switched off.
             Brian.
Unspoiled by progress.

Offline mrjones

  • Trade Count: (0)
  • Registered Bridgestone Member
  • **
  • Posts: 17
Re: Replacement rectifier/regulator wiring
« Reply #3 on: October 06, 2018, 10:36:31 AM »
 Yes i know this is an old thread but ive just looked on it for some advice, i have a reg/rec same as above ready to fit which has the three yellow wires and the black red green, my problem is red is usually live and black ground here your saying green is ground and black the sensor wire which goes to live (with the red) is there a way of testing which function the black and green wires have,without connecting them and possibly causing damage?

Offline mrjones

  • Trade Count: (0)
  • Registered Bridgestone Member
  • **
  • Posts: 17
Re: Replacement rectifier/regulator wiring
« Reply #4 on: October 06, 2018, 01:19:09 PM »
 i have spent a bit of time researching this and have found that most if not all reg/recs use a green wire for ground so i have answered my own question! or you could say google and ebay have!

 


Gallery


Views:23
Comments (0)
By: harleywaynecycles

Views:20
Comments (0)
By: harleywaynecycles

Views:17
Comments (0)
By: harleywaynecycles

Views:9
Comments (0)
By: harleywaynecycles

Classifieds

BS Keychain (SOLD)

Price: $0.00
Date: 11/23/2018 12:51 pm
Time Left: 68d 15h 51m
350 engine carb covers left an right show quality SOLD!!!
Price: $0.00
Date: 11/18/2018 06:13 pm
Time Left: 63d 21h 14m
Frame etc Bridgestone 350

Price: $0.00
Date: 11/15/2018 11:52 pm
Time Left: 471d 2h 53m
[ebay] ‘67 175 DT - no reserve
Price: $0.00
Date: 11/09/2018 10:20 am
Time Left: 54d 13h 21m

Recent Downloads added

11/01/1967 Factory Service Letter, RH shift/LH Brake conversion

Rating: (None)
Filesize: 92.56KB
Date: August 03, 2018, 02:49:08 AM
11/01/1967 Factory Service Letter, RH shift/LH Brake conversion

Rating: (None)
Filesize: 142.24KB
Date: August 03, 2018, 02:44:36 AM
350 GTR Wiring Diagram
Rating: *****
Filesize: 8604.23KB
Date: July 29, 2018, 12:29:25 PM
Bridgestone Motorcycles

Rating: (None)
Filesize: 3561.91KB
Date: June 05, 2018, 04:42:13 PM

Powered by EzPortal