Author Topic: BS 350 Racer Electrical Generation System Photos  (Read 4156 times)

0 Members and 1 Guest are viewing this topic.

Offline rwgibbon

  • Trade Count: (2)
  • Master Registered Bridgestone Member
  • *****
  • Posts: 578
  • 1968 BS 350 GTR
BS 350 Racer Electrical Generation System Photos
« on: February 15, 2017, 02:16:11 PM »
Bert Lilley is developing a new electrical generation system for his 2nd generation 350 Bridgestone Racer.

I have attached a few photographs of Bert's newest system.

Randy

Offline rwgibbon

  • Trade Count: (2)
  • Master Registered Bridgestone Member
  • *****
  • Posts: 578
  • 1968 BS 350 GTR
Re: BS 350 Racer Electrical Generation System Photos
« Reply #1 on: February 15, 2017, 02:17:25 PM »
Photograph 2

Offline rwgibbon

  • Trade Count: (2)
  • Master Registered Bridgestone Member
  • *****
  • Posts: 578
  • 1968 BS 350 GTR
Re: BS 350 Racer Electrical Generation System Photos
« Reply #2 on: February 15, 2017, 02:18:10 PM »
Photograph 3

Offline OldSwartout

  • Global Moderator
  • Trade Count: (0)
  • *******
  • Posts: 1314
Re: BS 350 Racer Electrical Generation System Photos
« Reply #3 on: February 15, 2017, 03:43:48 PM »
Nice.  Does it have a built-in electronic advance? Regardless, it looks like a great idea.
Karl Swartout
Mooresville, IN
BS175 Roadracer. BS200RS, BS350 GTR

Offline slawsonb

  • Trade Count: (0)
  • Master Registered Bridgestone Member
  • *****
  • Posts: 1398
Re: BS 350 Racer Electrical Generation System Photos
« Reply #4 on: February 15, 2017, 05:41:43 PM »
Very slick and should take less engine power to rotate than a stock BS dynamo with an electronic conversion.
...bert

Offline bert Lilley

  • Trade Count: (0)
  • Full Bridgestone Member
  • ***
  • Posts: 29
Re: BS 350 Racer Electrical Generation System Photos
« Reply #5 on: February 18, 2017, 04:59:03 PM »
As far as i know Karl the PVL systems do/can come with a ignition curve. This one i don't know truly I bought it on Ebay and it was listed as "Sat on the shelf for years" i do hope it even works it was listed as a Yamaha 350 twin Race Ignition.
So if it work's on the RD350,RZ350 and the Banshee twins no reason it should not work on our Bridgestones.

Regardless i am proceeding forward and when i get it mounted in my #2 Engine I'll run it and observe the ignition timing with a strobe light and adjust accordingly i am for 2m BTDC.

Once its runs , i'll do up some sketches of the rascal and get them posted on this site for future Ref.

Regards Bert

Offline bsracer

  • Trade Count: (0)
  • Expert Registered Bridgestone Member
  • ****
  • Posts: 344
Re: BS 350 Racer Electrical Generation System Photos
« Reply #6 on: February 19, 2017, 11:02:14 AM »
I like your setup so far. I run the ARD (which is for a Banshee) ignition on my 175 at 2mm BTDC. Has run pretty flawlessly. The only problem I have is oil from the transmission makes it's way past two orings in the housing and the ignition mount keeps breaking. The new ignition I've got on the back burner will fit in the orig ignition housing and hopefully won't leak.

paul

p.s. ironically I've taken apart a bunch a motors, mostly 200's that had RTV silicon all over the oring on the ignition housing. I'm guessing when BS went to the ignition spinning at full speed, the oring wasn't enough to retain the trans oil.
« Last Edit: February 19, 2017, 11:11:54 AM by bsracer »

Offline bert Lilley

  • Trade Count: (0)
  • Full Bridgestone Member
  • ***
  • Posts: 29
Re: BS 350 Racer Electrical Generation System Photos
« Reply #7 on: March 12, 2017, 03:03:46 PM »
Thanks for the heads up Regarding the "O" ring mumm have to give it a good look over. I am going to install new Oil seals .
but thanks for the Info.
Bert

 


Gallery


Views:219
Comments (0)
By: Jon West

Views:1360
Comments (0)
By: rwgibbon

Views:1690
Comments (0)
By: Perry L Anderson

Views:1755
Comments (0)
By: Perry L Anderson

Classifieds

Gto
Date: 03/02/2024 06:49 am
Time Left:
Looking for a BS90 used or new luggage Carrier assembly

Date: 02/01/2024 04:19 pm
Time Left:
Gto
Date: 10/19/2023 01:08 pm
Time Left:
Urgent - l/end roller bearing & piston pins needed
Date: 10/08/2023 03:25 am
Time Left:

Recent Downloads added

Chibi, Chibi Deluxe, Tora Service Manual
Rating: (None)
Filesize: 20383.27KB
Date: May 01, 2023, 08:35:39 PM
Chibi_Tora_Parts_Manual
Rating: (None)
Filesize: 14301.44KB
Date: May 01, 2023, 08:25:53 PM
BS200 Mk II RS & MK II SS Exclusive Parts
Rating: (None)
Filesize: 358.29KB
Date: March 07, 2021, 07:30:10 PM
1970 sales brochure
Rating: *****
Filesize: 6753.33KB
Date: July 16, 2020, 10:01:18 PM

Powered by EzPortal