Author Topic: Oil pump HS175  (Read 2333 times)

0 Members and 1 Guest are viewing this topic.

mnmrider

  • Guest
  • Trade Count: (0)
Oil pump HS175
« on: June 20, 2017, 06:51:07 PM »
I need to pull the oil pump and could use some advice for this. It leaks about everywhere, mainly because the bolts are quite loose. Any thoughts on taking it off and then reassembling it?
Advice greatly appreciated!
Thanks.
Marc

Offline BRT-GTR

  • Brian
  • Trade Count: (0)
  • Master Registered Bridgestone Member
  • *****
  • Posts: 951
Re: Oil pump HS175
« Reply #1 on: June 21, 2017, 05:39:08 AM »
       Hi Marc,
                  Here's a link to the definitive guide to stripping and rebuilding the 175 pump, courtesy of our departed friend Graham Weeks (Disc_Valve).

                   http://bridgestonemotorcycleparts.com/index.php?topic=3640.msg19666#msg19666

    If this doesn't help you sort the problem, nothing will  ;D ;).   Good luck,       Brian.
« Last Edit: June 21, 2017, 05:47:19 AM by BRT-GTR »
Unspoiled by progress.
I'm so glad I grew up in the 60s & 70s. I did so much stupid stuff and there's no record of it.............Anywhere !!

mnmrider

  • Guest
  • Trade Count: (0)
Re: Oil pump HS175
« Reply #2 on: June 21, 2017, 11:08:54 AM »
Thanks a lot. That's just what I needed.
Marc

jjwithers

  • Guest
  • Trade Count: (0)
Re: Oil pump HS175
« Reply #3 on: November 25, 2017, 08:59:31 PM »
I am going to try to hijack this thread -
I recently went through engine rebuild #2 after detonating a piston.
Unfortunately, I got it running and then a week later, had to get back surgery.  SO no riding for me for at least a few more weeks. 
I am noticing that the oil pump is leaking a bit of injection oil onto the cardboard I parked it on. 

Should it have a valve in there of sorts that stops the oil from entering the engine?   I am worried about oil building up in the engine while not riding it. I hope it is stopping at the pump and coming out at that point.  The drip is coming from the bottom of the pump.  Not sure the source but perhaps the rubber feed line.
I can't bend over to look at it more closely until I heal more. 

Has anybody installed, or would there ever be a need for a petcock of sorts to kill the oil feed while parked for long term? 

Are these pumps prone to leaks?


Offline OldSwartout

  • Global Moderator
  • Trade Count: (0)
  • *******
  • Posts: 1314
Re: Oil pump HS175
« Reply #4 on: November 25, 2017, 09:38:47 PM »
Typically, they don't leak, either to the outside or into the engine.  It is likely the rubber inlet hose or the gaskets on the banjo fitting or the banjo itself is cracked.

Having said that, I think my 175HS may leak injection oil into the engine while sitting.  The last couple of times I've started it, it smoked heavily for a few miles from the right side. I don't think it's the rotary valve seal leaking transmission oil into the crankcase because the level isn't high enough for that to happen. There was also injection oil in the carburetor throat the last time I took the side cover off.

Maybe someone else has some different experiences or ideas to share.
Karl Swartout
Mooresville, IN
BS175 Roadracer. BS200RS, BS350 GTR

Offline BRT-GTR

  • Brian
  • Trade Count: (0)
  • Master Registered Bridgestone Member
  • *****
  • Posts: 951
Re: Oil pump HS175
« Reply #5 on: November 26, 2017, 04:30:33 PM »
          In my experience, the modern, high performance 2S oils are extremely searching and will leak for fun  :-[ ;)

   I've had the pump off my GTO 2 or 3 times this summer, the last time to finally 'sort it' and I noticed the other day it's still got a drip from the carb cover drain. What do I have to do to keep the ******y stuff inside the pump ??, And yes, I have found it in the carb throat and the starter plunger chamber. Should be worth trying for anyone with a time siezed cylinder.

    Getting a bit cold in the workshop to investigate what's going on, so it's got a takeaway tray underneath until I feel motivated !!                             Brian.
Unspoiled by progress.
I'm so glad I grew up in the 60s & 70s. I did so much stupid stuff and there's no record of it.............Anywhere !!

jjwithers

  • Guest
  • Trade Count: (0)
Re: Oil pump HS175
« Reply #6 on: November 27, 2017, 12:55:38 PM »
what kind/size rubber hose are you guys using?  I have a stock piece of rubber hose but it may be the problem. I'm also interested in size to see if there is an in-line shut off valve I can install for when the bike is not in use.
humm....

jjwithers

  • Guest
  • Trade Count: (0)
Re: Oil pump HS175
« Reply #7 on: December 14, 2017, 04:52:13 AM »
FWIW some info I gathered - 
Oil line can be fuel line from a motorcycle or lawn mower shop. 3/16" or 5mm non-reinforced. Anything that's intended for fuel will last a long time with oil.

 


Gallery


Views:221
Comments (0)
By: Jon West

Views:1362
Comments (0)
By: rwgibbon

Views:1691
Comments (0)
By: Perry L Anderson

Views:1757
Comments (0)
By: Perry L Anderson

Classifieds

Gto
Date: 03/02/2024 06:49 am
Time Left:
Looking for a BS90 used or new luggage Carrier assembly

Date: 02/01/2024 04:19 pm
Time Left:
Gto
Date: 10/19/2023 01:08 pm
Time Left:
Urgent - l/end roller bearing & piston pins needed
Date: 10/08/2023 03:25 am
Time Left:

Recent Downloads added

Chibi, Chibi Deluxe, Tora Service Manual
Rating: (None)
Filesize: 20383.27KB
Date: May 01, 2023, 08:35:39 PM
Chibi_Tora_Parts_Manual
Rating: (None)
Filesize: 14301.44KB
Date: May 01, 2023, 08:25:53 PM
BS200 Mk II RS & MK II SS Exclusive Parts
Rating: (None)
Filesize: 358.29KB
Date: March 07, 2021, 07:30:10 PM
1970 sales brochure
Rating: *****
Filesize: 6753.33KB
Date: July 16, 2020, 10:01:18 PM

Powered by EzPortal