Author Topic: BS 350 Racer Electrical Generation System Photos  (Read 792 times)

0 Members and 1 Guest are viewing this topic.

Offline rwgibbon

  • Trade Count: (2)
  • Expert Registered Bridgestone Member
  • ****
  • Posts: 380
  • 1968 BS 350 GTR
BS 350 Racer Electrical Generation System Photos
« on: February 15, 2017, 02:16:11 PM »
Bert Lilley is developing a new electrical generation system for his 2nd generation 350 Bridgestone Racer.

I have attached a few photographs of Bert's newest system.

Randy

Offline rwgibbon

  • Trade Count: (2)
  • Expert Registered Bridgestone Member
  • ****
  • Posts: 380
  • 1968 BS 350 GTR
Re: BS 350 Racer Electrical Generation System Photos
« Reply #1 on: February 15, 2017, 02:17:25 PM »
Photograph 2

Offline rwgibbon

  • Trade Count: (2)
  • Expert Registered Bridgestone Member
  • ****
  • Posts: 380
  • 1968 BS 350 GTR
Re: BS 350 Racer Electrical Generation System Photos
« Reply #2 on: February 15, 2017, 02:18:10 PM »
Photograph 3

Offline OldSwartout

  • Global Moderator
  • Trade Count: (0)
  • *******
  • Posts: 947
Re: BS 350 Racer Electrical Generation System Photos
« Reply #3 on: February 15, 2017, 03:43:48 PM »
Nice.  Does it have a built-in electronic advance? Regardless, it looks like a great idea.
Karl Swartout
Mooresville, IN
BS175 Roadracer
BS350 GTR

Offline slawsonb

  • Trade Count: (0)
  • Master Registered Bridgestone Member
  • *****
  • Posts: 1347
Re: BS 350 Racer Electrical Generation System Photos
« Reply #4 on: February 15, 2017, 05:41:43 PM »
Very slick and should take less engine power to rotate than a stock BS dynamo with an electronic conversion.
...bert

Offline bert Lilley

  • Trade Count: (0)
  • Registered Bridgestone Member
  • **
  • Posts: 20
Re: BS 350 Racer Electrical Generation System Photos
« Reply #5 on: February 18, 2017, 04:59:03 PM »
As far as i know Karl the PVL systems do/can come with a ignition curve. This one i don't know truly I bought it on Ebay and it was listed as "Sat on the shelf for years" i do hope it even works it was listed as a Yamaha 350 twin Race Ignition.
So if it work's on the RD350,RZ350 and the Banshee twins no reason it should not work on our Bridgestones.

Regardless i am proceeding forward and when i get it mounted in my #2 Engine I'll run it and observe the ignition timing with a strobe light and adjust accordingly i am for 2m BTDC.

Once its runs , i'll do up some sketches of the rascal and get them posted on this site for future Ref.

Regards Bert

Offline bsracer

  • Trade Count: (0)
  • Expert Registered Bridgestone Member
  • ****
  • Posts: 284
Re: BS 350 Racer Electrical Generation System Photos
« Reply #6 on: February 19, 2017, 11:02:14 AM »
I like your setup so far. I run the ARD (which is for a Banshee) ignition on my 175 at 2mm BTDC. Has run pretty flawlessly. The only problem I have is oil from the transmission makes it's way past two orings in the housing and the ignition mount keeps breaking. The new ignition I've got on the back burner will fit in the orig ignition housing and hopefully won't leak.

paul

p.s. ironically I've taken apart a bunch a motors, mostly 200's that had RTV silicon all over the oring on the ignition housing. I'm guessing when BS went to the ignition spinning at full speed, the oring wasn't enough to retain the trans oil.
« Last Edit: February 19, 2017, 11:11:54 AM by bsracer »

Offline bert Lilley

  • Trade Count: (0)
  • Registered Bridgestone Member
  • **
  • Posts: 20
Re: BS 350 Racer Electrical Generation System Photos
« Reply #7 on: March 12, 2017, 03:03:46 PM »
Thanks for the heads up Regarding the "O" ring mumm have to give it a good look over. I am going to install new Oil seals .
but thanks for the Info.
Bert

 


Gallery


Views:14
Comments (0)
By: AlanJohn

Views:13
Comments (0)
By: AlanJohn

Views:14
Comments (0)
By: AlanJohn

Views:15
Comments (0)
By: AlanJohn

Classifieds

350 GTR/GTO Dynamo Points Base Plate & Case Screws

Price: $0.00
Date: 09/14/2017 01:44 pm
Time Left: 78d 3h 7m
SUPER RARE 1965 BRIDGESTONE HUMP BACK SPORT 90.

Price: $1400.00
Date: 09/03/2017 02:02 pm
Time Left: 67d 3h 25m
Searching For Parts To Complete A 350 GTR

Date: 09/02/2017 05:19 pm
Time Left: 66d 6h 42m
Handle Bars with controls
Date: 08/17/2017 04:27 pm
Time Left: 50d 5h 50m

Recent Downloads added

How to build a 149 mph 350GTR....
Rating: (None)
Filesize: 7154.56KB
Date: April 18, 2017, 08:25:38 AM
Bridgestone 100 Sport Brochure
Rating: *****
Filesize: 937.72KB
Date: July 08, 2015, 12:58:53 PM
BS 100 Sport Australian Brochure
Rating: *****
Filesize: 937.53KB
Date: June 29, 2015, 06:40:40 PM
Bridgestone 350 GTO - Moto L├ęgende May 2003
Rating: *****
Filesize: 9429.41KB
Date: April 22, 2015, 04:18:43 PM

Powered by EzPortal