Author Topic: Timing Marks?  (Read 616 times)

0 Members and 1 Guest are viewing this topic.

Offline TangoZulu

  • Current Roster:
  • Trade Count: (0)
  • Registered Bridgestone Member
  • **
  • Posts: 10
Timing Marks?
« on: January 15, 2018, 04:28:50 PM »
 So, time to disassemble the engine. But before I pull it apart, I want to know I'll be putting it together again so it will run: i.e. timed correctly. After pulling the right crankcase cover, I discover stamped dots on ALL of the gears. One on the Alternator, two on the fiber idler gear, one on the drive gear and two on the clutch gear ring. Woohoo. First of all, the pictures in the "Technical Handbook" look nothing like my gears (earlier model apparently. my '70 is model 16R.....) The dealer service letter says there are "no marks" on the idler gear. Not! So, if I spin it a bunch, I eventually wind up with a line up of dots that looks purposeful (photo). But is this correct? When they are lined up thus, the timing indentation on the flywheel is about an inch away from the "pin" (a shiny new wheel adjustor bolt) in the timing hole. So, when I put it together, how are all these timing dots supposed to look? What's the relevance to the timing mark on the flywheel? HELP!
1970 Hurricane Scrambler
1971 Norton Commando 750 Roadster
2007 Moto Guzzi Breva 750
2009 Moto Guzzi Norge 1200

Online BRT-GTR

  • Brian
  • Trade Count: (0)
  • Master Registered Bridgestone Member
  • *****
  • Posts: 676
Re: Timing Marks?
« Reply #1 on: January 16, 2018, 01:19:36 PM »
                 See Page 23 of the aftermarket Clymer manual in the download section, mentions the fibre gear, it looks like your  timing marks are correctly lined up. I guess a previous owner has marked the fibre idler gear.
            The timing pin should drop into the timing hole when one of the points open, not necessarily exactly when the timing marks line up although it will be near as you have found. Check the points opening against the timing hole, you should find it is correct or very close (could need adjusting).
           Brian.
« Last Edit: January 18, 2018, 08:45:58 AM by BRT-GTR »
Unspoiled by progress.

Offline OldSwartout

  • Global Moderator
  • Trade Count: (0)
  • *******
  • Posts: 1013
Re: Timing Marks?
« Reply #2 on: January 19, 2018, 02:27:18 PM »
I agree you've got it lined up right.  I don't see the marks on the clutch in your photo, you'll find the clutch gear also has marks on it to line up with the crankshaft gear and the fiber gear marks; however, they are usually somewhat difficult to see, not as obvious as the others.
Karl Swartout
Mooresville, IN
BS175 Roadracer
BS350 GTR

Offline TangoZulu

  • Current Roster:
  • Trade Count: (0)
  • Registered Bridgestone Member
  • **
  • Posts: 10
Re: Timing Marks?
« Reply #3 on: January 19, 2018, 07:38:25 PM »
I figured the clutch marks (of which there were two) were irrelevant,
1970 Hurricane Scrambler
1971 Norton Commando 750 Roadster
2007 Moto Guzzi Breva 750
2009 Moto Guzzi Norge 1200

Offline OldSwartout

  • Global Moderator
  • Trade Count: (0)
  • *******
  • Posts: 1013
Re: Timing Marks?
« Reply #4 on: January 20, 2018, 08:22:52 AM »
They are as long as you're careful to get the alignment like you have in the photo.
Karl Swartout
Mooresville, IN
BS175 Roadracer
BS350 GTR

Online BRT-GTR

  • Brian
  • Trade Count: (0)
  • Master Registered Bridgestone Member
  • *****
  • Posts: 676
Re: Timing Marks?
« Reply #5 on: January 20, 2018, 08:50:03 AM »
            The marks on the fibre gear are also irrelevant, just easier to use them if they are there.
Also means you know the timing is right before you complete the engine, which was the basis of your original enquiry.
« Last Edit: January 20, 2018, 09:27:52 AM by BRT-GTR »
Unspoiled by progress.

Offline mybridgestones

  • Trade Count: (0)
  • Full Bridgestone Member
  • ***
  • Posts: 34
Re: Timing Marks?
« Reply #6 on: March 01, 2018, 03:11:52 PM »
Remember that some of the manuals cover the early type generator, so it may look different on your engine.
I always mark the dots with a felt pen to make it easier to identify when assembling the engine.
All the dots have to line up or ignition timing is impossible to achieve.
This is how it's supposed to look.
Stu

 


Gallery


Views:21
Comments (1)
By: fahrkle

Views:56
Comments (1)
By: Geoff S

Views:53
Comments (0)
By: AlanJohn

Views:64
Comments (3)
By: mybridgestones

Classifieds

Misc 1968 Bridgestone 90 parts wanted
Date: 04/16/2018 03:09 pm
Time Left: 87d 9h 25m
Neutral switch for 350
Date: 04/15/2018 03:14 pm
Time Left: 86d 9h 30m
GTO diffuser seals
Date: 04/08/2018 04:27 am
Time Left: 78d 22h 43m
GTO stingers diffusers
Date: 04/02/2018 06:29 am
Time Left: 73d 0h 45m

Recent Downloads added

How to build a 149 mph 350GTR....
Rating: (None)
Filesize: 7154.56KB
Date: April 18, 2017, 08:25:38 AM
Bridgestone 100 Sport Brochure
Rating: *****
Filesize: 937.72KB
Date: July 08, 2015, 12:58:53 PM
BS 100 Sport Australian Brochure
Rating: *****
Filesize: 937.53KB
Date: June 29, 2015, 06:40:40 PM
Bridgestone 350 GTO - Moto L├ęgende May 2003
Rating: *****
Filesize: 9429.41KB
Date: April 22, 2015, 04:18:43 PM

Powered by EzPortal