Author Topic: Header/muffler joint  (Read 973 times)

0 Members and 1 Guest are viewing this topic.

Offline TangoZulu

  • Current Roster:
  • Trade Count: (0)
  • Registered Bridgestone Member
  • **
  • Posts: 10
Header/muffler joint
« on: December 29, 2017, 01:57:54 PM »
I've a recently acquired 1970 175HS. While I've restored a number of bikes over the years, and built 3 Cafe Racers, this is both my first Bridgestone and first 2-stroke project. I'll probably need to candle the minds of the membership for a variety of things, but an early one that came up was the connector between the header pipes and mufflers. My bike came with some kind of what appears to be radiator hose held on with hose clamps. This is obviously not stock since the Parts Catalog has a part # for the muffler joint rubber. So, my question is, is this "modification" (what's the British idiom, bodged?) what is typically done and acceptable? Why? Because the stock joint rubber is unobtainable, or doesn't work, or too expensive, or? Or is it preferable to use the stock joint rubber because Richard has a warehouse full of 'em?
1970 Hurricane Scrambler
1971 Norton Commando 750 Roadster
2007 Moto Guzzi Breva 750
2009 Moto Guzzi Norge 1200

Offline dcr

  • Trade Count: (0)
  • Expert Registered Bridgestone Member
  • ****
  • Posts: 430
Re: Header/muffler joint
« Reply #1 on: December 29, 2017, 03:24:40 PM »
Richard usually has them listed on eBay. The radiator hose seems to be a standard "make due" solution although I'm not sure they hold up for long. I bought 2 bikes that had a chunk of radiator hose and hose clamps in place of the standard piece.
1966 175 DT and 1968 350 GTR

Offline jjwithers

  • Trade Count: (0)
  • Full Bridgestone Member
  • ***
  • Posts: 97
    • Beemers and Bits
Re: Header/muffler joint
« Reply #2 on: January 07, 2018, 09:59:18 PM »
Any ideas on better clamps then those little wire clamps for this union between the two pipes?
I have been looking for a thin hose clamp of that diameter and have not had any luck.  I get some gunk coming out of that rubber even though I have new rubber. 
1967 175 HS
and some BMW's from the 60's and 70's

Offline OldSwartout

  • Global Moderator
  • Trade Count: (0)
  • *******
  • Posts: 1073
Re: Header/muffler joint
« Reply #3 on: January 08, 2018, 08:32:56 AM »
I haven't tried this, but it could help, they would provide more tension than the BS parts. They're available in 1/8" increments. You may be able to find the right size locally.

https://www.mcmaster.com/#hose-clamps/=1b1cnrl
Karl Swartout
Mooresville, IN
BS175 Roadracer
BS350 GTR

Offline coxy

  • coxy
  • Trade Count: (0)
  • Master Registered Bridgestone Member
  • *****
  • Posts: 1105
Re: Header/muffler joint
« Reply #4 on: January 10, 2018, 04:36:09 PM »
you could probably get some clamps for pod filters that would fit

 


Gallery


Views:23
Comments (0)
By: harleywaynecycles

Views:20
Comments (0)
By: harleywaynecycles

Views:17
Comments (0)
By: harleywaynecycles

Views:9
Comments (0)
By: harleywaynecycles

Classifieds

BS Keychain (SOLD)

Price: $0.00
Date: 11/23/2018 12:51 pm
Time Left: 67d 9h 56m
350 engine carb covers left an right show quality SOLD!!!
Price: $0.00
Date: 11/18/2018 06:13 pm
Time Left: 62d 15h 19m
Frame etc Bridgestone 350

Price: $0.00
Date: 11/15/2018 11:52 pm
Time Left: 469d 20h 58m
[ebay] ‘67 175 DT - no reserve
Price: $0.00
Date: 11/09/2018 10:20 am
Time Left: 53d 7h 26m

Recent Downloads added

11/01/1967 Factory Service Letter, RH shift/LH Brake conversion

Rating: (None)
Filesize: 92.56KB
Date: August 03, 2018, 02:49:08 AM
11/01/1967 Factory Service Letter, RH shift/LH Brake conversion

Rating: (None)
Filesize: 142.24KB
Date: August 03, 2018, 02:44:36 AM
350 GTR Wiring Diagram
Rating: *****
Filesize: 8604.23KB
Date: July 29, 2018, 12:29:25 PM
Bridgestone Motorcycles

Rating: (None)
Filesize: 3561.91KB
Date: June 05, 2018, 04:42:13 PM

Powered by EzPortal