Author Topic: cranky  (Read 527 times)

0 Members and 1 Guest are viewing this topic.

Offline coxy

  • coxy
  • Trade Count: (0)
  • Master Registered Bridgestone Member
  • *****
  • Posts: 1078
cranky
« on: October 13, 2017, 02:45:14 PM »
gday guys
I know ive got to lash out and buy some new crank bearings .ive got three straight cranks with bad bearings and one bent crank with good bearings(near new condition) has anyone ever been able to re use crank bearings for a rebuild or do they get destroyed when pulling them apart ?

Offline OldSwartout

  • Global Moderator
  • Trade Count: (0)
  • *******
  • Posts: 1017
Re: cranky
« Reply #1 on: October 13, 2017, 10:14:02 PM »
I've reused them more than once on my road racer with no issues, but you need a bearing puller that will pull them without a lot of hammering.  Something like this: https://www.amazon.com/OEMTOOLS-27084-Bearing-Separator-Splitter/dp/B004FEHZ82/ref=sr_1_8/140-2993387-5752426?ie=UTF8&qid=1507947167&sr=8-8&keywords=bearing+separator
Karl Swartout
Mooresville, IN
BS175 Roadracer
BS350 GTR

Offline coxy

  • coxy
  • Trade Count: (0)
  • Master Registered Bridgestone Member
  • *****
  • Posts: 1078
Re: cranky
« Reply #2 on: October 14, 2017, 02:55:34 PM »
thanks karl

Offline hardy

  • Trade Count: (0)
  • Full Bridgestone Member
  • ***
  • Posts: 153
Re: cranky
« Reply #3 on: October 14, 2017, 07:02:39 PM »
As Karl said, if you could get a good pull from the inner race, with out side loading the bearing, then there is no reason it wouldn’t be possible.

Half moon pullers are great for this, I have a cheap flea bay kit, but they they are quite thick to compensate for the cheapness of the steel used. The high quality ones we have at work are very thin to allow installation into those tight areas.

Hardy

Offline BRT-GTR

  • Brian
  • Trade Count: (0)
  • Master Registered Bridgestone Member
  • *****
  • Posts: 683
Re: cranky
« Reply #4 on: October 17, 2017, 04:16:38 PM »
            Even the half moon type pullers exert the pull on the outer race but that's ok as long as you dont have to use a hammer to get the bearings moving on the shaft. It's hammering that will dent the races and drastically shorten the life of the bearing.
        Clean the shaft, maybe a light rub with very fine wet or dry paper and oil the shaft before pulling.
I've pulled the outer crank bearings before now to replace the crank seals and reused them without any problems.
                     Brian.
Unspoiled by progress.

 


Gallery


Views:26
Comments (1)
By: fahrkle

Views:60
Comments (1)
By: Geoff S

Views:53
Comments (0)
By: AlanJohn

Views:66
Comments (3)
By: mybridgestones

Classifieds

Seat Pan, Seat or quality cover
Date: 04/23/2018 02:27 pm
Time Left: 86d 12h 8m
Misc 1968 Bridgestone 90 parts wanted
Date: 04/16/2018 03:09 pm
Time Left: 79d 12h 50m
Neutral switch for 350
Date: 04/15/2018 03:14 pm
Time Left: 78d 12h 55m
GTO diffuser seals
Date: 04/08/2018 04:27 am
Time Left: 71d 2h 8m

Recent Downloads added

How to build a 149 mph 350GTR....
Rating: (None)
Filesize: 7154.56KB
Date: April 18, 2017, 08:25:38 AM
Bridgestone 100 Sport Brochure
Rating: *****
Filesize: 937.72KB
Date: July 08, 2015, 12:58:53 PM
BS 100 Sport Australian Brochure
Rating: *****
Filesize: 937.53KB
Date: June 29, 2015, 06:40:40 PM
Bridgestone 350 GTO - Moto Légende May 2003
Rating: *****
Filesize: 9429.41KB
Date: April 22, 2015, 04:18:43 PM

Powered by EzPortal