Author Topic: Motor earthing issue  (Read 756 times)

0 Members and 1 Guest are viewing this topic.

Offline hardy

  • Trade Count: (0)
  • Full Bridgestone Member
  • ***
  • Posts: 160
Motor earthing issue
« on: June 09, 2017, 03:28:52 AM »
Hey guys,

I started my bike this arvo in the garage with door down, (dumb idea, but found the air leaks in the garage lol) but while it was semi dark I noticed that the spring that covers the throttle cable was touching and earthing out on the barrel...strange

Is there a designated earth for the motor? Or have people installed a second earth to compensate?

Any ideas welcomed, bike starts and runs well.

Ryan

Offline BS Mechanic

  • Trade Count: (0)
  • Expert Registered Bridgestone Member
  • ****
  • Posts: 256
Re: Motor earthing issue
« Reply #1 on: June 09, 2017, 01:39:59 PM »
You should have a black-white wire coming out of the alternator and going to the battery negative. This grounds the engine.  There's also a black wire going from the battery negative to frame ground, although I can't quite remember where on the frame it goes.  Schematic in the shop manual shows the wires and connections.

Offline BRT-GTR

  • Brian
  • Trade Count: (0)
  • Master Registered Bridgestone Member
  • *****
  • Posts: 703
Re: Motor earthing issue
« Reply #2 on: June 10, 2017, 07:20:07 AM »
             The longer of the black earth wires coming from the battery negative goes to the rear frame mounting bolt on the voltage regulator. (The shorter wire goes to the rear terminal on the rectifier). It's not arranged quite as shown in the electrics schematic.

           With the motor being rubber mounted, it's not a bad idea to install a better, separate earthing wire for the engine. The long 6mm nut on the alternator strap provides a good connection at the crankcase and is easily connected to one of the adjacent frame bolts for the rear engine mount. Not original but helps prevent stray currents from trying to find an alternative route to earth on the frame. Surprised BS didn't fit one.
           Brian.
« Last Edit: June 12, 2017, 09:16:04 AM by BRT-GTR »
Unspoiled by progress.

Offline hardy

  • Trade Count: (0)
  • Full Bridgestone Member
  • ***
  • Posts: 160
Re: Motor earthing issue
« Reply #3 on: June 10, 2017, 06:15:49 PM »
Thanks for your replys guys. I will chase the wiring and check, but most likely install a better earth as suggested.

Ryan

 


Gallery


Views:14
Comments (1)
By: killerterp

Views:28
Comments (0)
By: rwgibbon

Views:53
Comments (1)
By: fahrkle

Views:82
Comments (1)
By: Geoff S

Classifieds

350 GTR/GTO Carbs (Set #2)

Price: $0.00
Date: 06/21/2018 01:29 pm
Time Left: 89d 23h 5m
350 GTR/GTO Wiring Package

Price: $0.00
Date: 06/19/2018 01:33 pm
Time Left: 87d 23h 10m
Wanted BS 100 Sport Fuel Tank and Muffler
Date: 06/14/2018 03:46 pm
Time Left: 83d 1h 22m
Need 350 clutch hub

Date: 06/11/2018 10:09 am
Time Left: 79d 19h 46m

Recent Downloads added

Bridgestone Motorcycles

Rating: (None)
Filesize: 3561.91KB
Date: June 05, 2018, 04:42:13 PM
Bridgestone Magazine Article

Rating: (None)
Filesize: 3561.91KB
Date: June 05, 2018, 04:38:08 PM
How to build a 149 mph 350GTR....
Rating: (None)
Filesize: 7154.56KB
Date: April 18, 2017, 08:25:38 AM
Bert Lilley's BS 350 Racer Modifications
Rating: (None)
Filesize: 0KB
Date: January 09, 2017, 04:27:24 PM

Powered by EzPortal