Author Topic: When is a carburetor beyond rebuilding?  (Read 2912 times)

0 Members and 1 Guest are viewing this topic.

Offline MZ250

  • Trade Count: (0)
  • Registered Bridgestone Member
  • **
  • Posts: 9
When is a carburetor beyond rebuilding?
« on: March 25, 2016, 02:40:16 PM »
Good afternoon, folks! I am working on an old carb, and am looking for advice regarding whether it's worth the trouble to rebuild. It has a bit of white, crusty build-up in the bowl and float chamber, having sat for a few decades. I got a kit with all gaskets, float valve, needle valve, adjustment screws, springs and clips. Advice I have found elsewhere on the web says that a carb with internal oxidation is beyond repair and should be entirely renewed. Is this accurate, or is there hope yet? The last carb I cleaned and reused (of similar age and condition) worked only for one day, then, in spite of repeated vigorous cleanings, NEVER ran the bike again, and I had to replace it. I did not use a full rebuild kit.  I have limited experience in such matters, and I am hoping that some of the more seasoned of you out there may be willing to offer their two pence. Much obliged!
1974 MZ TS250, Restored. 1960-something Honda S65, almost done! 1979 Honda Cx-500, Daily rider.

"Patience is the only real talent."

Offline coxy

  • coxy
  • Trade Count: (0)
  • Master Registered Bridgestone Member
  • *****
  • Posts: 1051
Re: When is a carburetor beyond rebuilding?
« Reply #1 on: March 25, 2016, 02:56:26 PM »
You may need ultra sonic cleaning. Steve Reed may be able to help you

Offline slawsonb

  • Trade Count: (0)
  • Master Registered Bridgestone Member
  • *****
  • Posts: 1351
Re: When is a carburetor beyond rebuilding?
« Reply #2 on: March 25, 2016, 03:10:44 PM »
The ultrasonic cleaning advice is best, but a good set of small brushes and lots elbow grease will go a long way. My vote is that all is not lost.
...bert

Offline MZ250

  • Trade Count: (0)
  • Registered Bridgestone Member
  • **
  • Posts: 9
Re: When is a carburetor beyond rebuilding?
« Reply #3 on: March 25, 2016, 03:55:29 PM »
Excellent, thanks for your prompt replies! I almost forgot, I do have an ultrasonic cleaner, albeit a cheap one. I will give that a go, as I have already applied quite a bit of brushed on elbow grease, if you will...
1974 MZ TS250, Restored. 1960-something Honda S65, almost done! 1979 Honda Cx-500, Daily rider.

"Patience is the only real talent."

Offline Old BS Guy

  • Trade Count: (0)
  • Full Bridgestone Member
  • ***
  • Posts: 83
Re: When is a carburetor beyond rebuilding?
« Reply #4 on: March 25, 2016, 05:57:00 PM »
There is a household cleaning product called CLR that is a lime and mineral descaler for showers and fixtures. I recently tried it in a diluted form on a carb. The jets were so plugged that not even my cleaning tool would touch them. I soaked the complete disassembled unit and parts in CLR for a day, and then rinsed with water, and blew it out. Came out perfectly clean. I chased all the jets with my cleaning tool,and they were clean. Just for good measure, I chased the passages with some aerosol carb cleaner, and blew them again. Carb was fine. On older carbs, pay attention in particular to the slide for excessive wear, and the needle and it's corresponding nozzle for wear, or being eccentric. Remember when you go back together to leave enough cable slack for proper slide adjustment when setting the idle, then readjust the cable to specified slack. Also, on plunger style chokes, don't expose the rubber sealing pad to caustic cleaners, as it will swell them out of dimension. Check that pad to make sure it will seal off the orifice when the choke is shut.

....KP
'69 Mach II RS, '67 350 GTR, '66 Sport 90 o.i., '65 90M Surf Rider, '68 100 Trail, '71 100 TMX ,'79 Honda CBX, '82 Yam 650 Turbo, '74 Norton 850 Hi-Rider, '74 Kaw H1F 500 Mach III, '75 Suz. GT-380,

Offline slawsonb

  • Trade Count: (0)
  • Master Registered Bridgestone Member
  • *****
  • Posts: 1351
Re: When is a carburetor beyond rebuilding?
« Reply #5 on: March 25, 2016, 07:07:32 PM »
One other thing to look for is the float pin holes becoming oblong from vibration. The out-of-round condition will make it difficult to set the float height and get it to remain constant when the carb is mounted. These holes can be bushed with brass, but the drilling process really requires setup in a mill or industrial drill press to hold the bore straight and to get both holes drilled in-line.
...bert

Offline Old BS Guy

  • Trade Count: (0)
  • Full Bridgestone Member
  • ***
  • Posts: 83
Re: When is a carburetor beyond rebuilding?
« Reply #6 on: March 25, 2016, 07:35:47 PM »
Good Point, Bert. I usually use a precision drill press, or a 5th of whiskey to steady my hand.
....KP
'69 Mach II RS, '67 350 GTR, '66 Sport 90 o.i., '65 90M Surf Rider, '68 100 Trail, '71 100 TMX ,'79 Honda CBX, '82 Yam 650 Turbo, '74 Norton 850 Hi-Rider, '74 Kaw H1F 500 Mach III, '75 Suz. GT-380,

Offline MZ250

  • Trade Count: (0)
  • Registered Bridgestone Member
  • **
  • Posts: 9
Re: When is a carburetor beyond rebuilding?
« Reply #7 on: March 25, 2016, 10:01:50 PM »
CLR---now that's brilliant. Had some in the utility room, got it soaking now. Thanks a bunch, guys!

 Now, a tip on "carburetter" cleaning from the operating manual for my 1974 MZ, which I find rather amusing: "Do not use a needle or piece of wire for cleaning the calibrated holes of the jets, because this will render them completely useless, use a bristle from mother's broom." 

CLR is much faster than going all the way to my mom's house...
1974 MZ TS250, Restored. 1960-something Honda S65, almost done! 1979 Honda Cx-500, Daily rider.

"Patience is the only real talent."

Offline slawsonb

  • Trade Count: (0)
  • Master Registered Bridgestone Member
  • *****
  • Posts: 1351
Re: When is a carburetor beyond rebuilding?
« Reply #8 on: March 26, 2016, 12:10:11 PM »
Scotch please, KP. ;D ::) ;D
...bert

Online OldSwartout

  • Global Moderator
  • Trade Count: (0)
  • *******
  • Posts: 964
Re: When is a carburetor beyond rebuilding?
« Reply #9 on: March 27, 2016, 10:14:11 AM »
Now, a tip on "carburetter" cleaning from the operating manual for my 1974 MZ, which I find rather amusing: "Do not use a needle or piece of wire for cleaning the calibrated holes of the jets, because this will render them completely useless, use a bristle from mother's broom." 

I find it amusing that many places sell the set of ribbed wire welding tip cleaning tools as carburetor jet cleaning tools.  I wonder how many people actually use them for that and screw up the edges of the holes in the jets or resize them.

http://www.powersportsplace.com/parts/bkm-15-2212?seid=pspse1&gclid=CN7ijYSG4csCFQuPaQod9lAFrQ

If air and brake cleaner won't get the crud out, I usually pull a strand of copper wire out of some automotive wiring and use it. At least copper is soft enough not to damage a jet.
Karl Swartout
Mooresville, IN
BS175 Roadracer
BS350 GTR

Offline BS Mechanic

  • Trade Count: (0)
  • Expert Registered Bridgestone Member
  • ****
  • Posts: 253
Re: When is a carburetor beyond rebuilding?
« Reply #10 on: March 27, 2016, 02:53:47 PM »
If you're serious about working on carbs, get yourself a set of jet reamers.  They are long and thin tapered reams with a square shape and sharp edges.

They come in a set from hair thin to quit large, enough to cover all jet sizes and also all the various small holes in carburetors.  These will clean out things that no amount of solvent or soaking will remove.  You do need to be reasonably careful, as you can also enlarge the holes if you aren't careful.

Not cheap, but very effective.

The set I have is Stahlwille, number 11085.  Amazon has them, several other places also and are less expensive.

 


Gallery


Views:34
Comments (2)
By: OldSwartout

Views:47
Comments (2)
By: AlanJohn

Views:32
Comments (0)
By: AlanJohn

Views:35
Comments (0)
By: AlanJohn

Classifieds

unobtanium for sale
Price: $0.00
Date: 11/20/2017 12:51 am
Time Left: 87d 15h 15m
Steering Damper rod needed for GTR 350
Date: 11/03/2017 10:07 am
Time Left: 70d 23h 31m
Bridgestone Sport 100

Price: $175.00
Date: 10/31/2017 09:31 am
Time Left: 67d 22h 56m
1970 Bridgestone DT 175
Price: $1200.00
Date: 10/28/2017 06:08 pm
Time Left: 65d 7h 32m

Recent Downloads added

How to build a 149 mph 350GTR....
Rating: (None)
Filesize: 7154.56KB
Date: April 18, 2017, 08:25:38 AM
Bridgestone 100 Sport Brochure
Rating: *****
Filesize: 937.72KB
Date: July 08, 2015, 12:58:53 PM
BS 100 Sport Australian Brochure
Rating: *****
Filesize: 937.53KB
Date: June 29, 2015, 06:40:40 PM
Bridgestone 350 GTO - Moto L├ęgende May 2003
Rating: *****
Filesize: 9429.41KB
Date: April 22, 2015, 04:18:43 PM

Powered by EzPortal