Author Topic: 350 Crank Pin Size?  (Read 2174 times)

0 Members and 1 Guest are viewing this topic.

Offline moonpup

  • Laidback Purist
  • Trade Count: (0)
  • Master Registered Bridgestone Member
  • *****
  • Posts: 2264
350 Crank Pin Size?
« on: March 21, 2017, 07:27:33 PM »
Would anyone happen to have measurements for the 350 crank pins?  Length & diameter?
Confucius say... "Better to have Bridgestone than Kidneystone"

Offline moonpup

  • Laidback Purist
  • Trade Count: (0)
  • Master Registered Bridgestone Member
  • *****
  • Posts: 2264
Re: 350 Crank Pin Size?
« Reply #1 on: March 22, 2017, 05:29:59 PM »
Update: I been informed that they are 24mm x 52.6mm.  8)
Confucius say... "Better to have Bridgestone than Kidneystone"

Offline bert Lilley

  • Trade Count: (0)
  • Full Bridgestone Member
  • ***
  • Posts: 29
Re: 350 Crank Pin Size?
« Reply #2 on: March 23, 2017, 10:54:45 AM »

  Just Happen to have one on my Desk  :- Pin Diameter = 0.945" in Dia x 25.4 = 24mm dia. 
                                                       
                                                                  Pin Length = 2.072" x 25.4 = 52.6mm Long.

Hope this Helps  Bert

Offline moonpup

  • Laidback Purist
  • Trade Count: (0)
  • Master Registered Bridgestone Member
  • *****
  • Posts: 2264
Re: 350 Crank Pin Size?
« Reply #3 on: March 23, 2017, 07:55:13 PM »
Thank you for the confirmation Bert..... and yes, it does help.
Confucius say... "Better to have Bridgestone than Kidneystone"

Offline farmerdl

  • Trade Count: (0)
  • Full Bridgestone Member
  • ***
  • Posts: 145
Re: 350 Crank Pin Size?
« Reply #4 on: March 25, 2017, 09:24:09 AM »
What information is available regarding the heat treat on these pins? 

Offline OldSwartout

  • Global Moderator
  • Trade Count: (0)
  • *******
  • Posts: 1314
Re: 350 Crank Pin Size?
« Reply #5 on: March 25, 2017, 12:20:42 PM »
Crank pins are typical bearing journal specs, RC60-62 hardness. They can be relatively soft core, RC30-45 with either a nitrided case that will be .007-.015 deep or carburized which should provide from .020-.050 case depth. With the nitride heat treat, there's not much depth for finish grind after plus the thin case needs a harder core for support.
Karl Swartout
Mooresville, IN
BS175 Roadracer. BS200RS, BS350 GTR

Offline bsracer

  • Trade Count: (0)
  • Expert Registered Bridgestone Member
  • ****
  • Posts: 344
Re: 350 Crank Pin Size?
« Reply #6 on: March 26, 2017, 03:05:50 AM »
I just cut down some 175 pins to use for the crank jig and they were not soft in the center! Amazing how tough those things can be!

paul

 


Gallery


Views:220
Comments (0)
By: Jon West

Views:1362
Comments (0)
By: rwgibbon

Views:1690
Comments (0)
By: Perry L Anderson

Views:1757
Comments (0)
By: Perry L Anderson

Classifieds

Gto
Date: 03/02/2024 06:49 am
Time Left:
Looking for a BS90 used or new luggage Carrier assembly

Date: 02/01/2024 04:19 pm
Time Left:
Gto
Date: 10/19/2023 01:08 pm
Time Left:
Urgent - l/end roller bearing & piston pins needed
Date: 10/08/2023 03:25 am
Time Left:

Recent Downloads added

Chibi, Chibi Deluxe, Tora Service Manual
Rating: (None)
Filesize: 20383.27KB
Date: May 01, 2023, 08:35:39 PM
Chibi_Tora_Parts_Manual
Rating: (None)
Filesize: 14301.44KB
Date: May 01, 2023, 08:25:53 PM
BS200 Mk II RS & MK II SS Exclusive Parts
Rating: (None)
Filesize: 358.29KB
Date: March 07, 2021, 07:30:10 PM
1970 sales brochure
Rating: *****
Filesize: 6753.33KB
Date: July 16, 2020, 10:01:18 PM

Powered by EzPortal