Author Topic: Dynetek DS2-1 Conversion to Bridgestone Points Housing  (Read 357 times)

0 Members and 1 Guest are viewing this topic.

Offline billdok

  • Trade Count: (0)
  • Registered Bridgestone Member
  • **
  • Posts: 6
Dynetek DS2-1 Conversion to Bridgestone Points Housing
« on: May 13, 2018, 11:00:54 AM »
All I am attaching the an explanation and pictures which describe how I made the conversion. i hope this helps others.

Offline Steve Swan

  • Trade Count: (0)
  • Registered Bridgestone Member
  • **
  • Posts: 15
Re: Dynetek DS2-1 Conversion to Bridgestone Points Housing
« Reply #1 on: May 13, 2018, 03:14:24 PM »
Hi Bill,

Thank you for posting your conversion.

Steve Swan

Offline SR-175

  • Trade Count: (0)
  • Full Bridgestone Member
  • ***
  • Posts: 67
Re: Dynetek DS2-1 Conversion to Bridgestone Points Housing
« Reply #2 on: May 14, 2018, 11:26:41 AM »
Hi Bill,

I have fitted a Dynatek ignition to a BS 175 engine that I plan to run total loss. Can you confirm the wiring in attached is Ok, or, do I need any resistors or other items ?

Thanks .. ray

Offline OldSwartout

  • Global Moderator
  • Trade Count: (0)
  • *******
  • Posts: 1032
Karl Swartout
Mooresville, IN
BS175 Roadracer
BS350 GTR

Offline SR-175

  • Trade Count: (0)
  • Full Bridgestone Member
  • ***
  • Posts: 67
Re: Dynetek DS2-1 Conversion to Bridgestone Points Housing
« Reply #4 on: May 14, 2018, 01:09:37 PM »
Thank you !!


Offline billdok

  • Trade Count: (0)
  • Registered Bridgestone Member
  • **
  • Posts: 6
Re: Dynetek DS2-1 Conversion to Bridgestone Points Housing
« Reply #5 on: May 14, 2018, 05:28:29 PM »
Ray I believe "Old Swarthog" has answered your but question but in case you were still unsure, your wiring is correct. I believe "Old SwartHog" has also mentioned that you need need to have 3 ohms resistance including the coil resistance in the circuit and that is normally a resistor between +12volt and the coils.
Hope this helps.

Offline OldSwartout

  • Global Moderator
  • Trade Count: (0)
  • *******
  • Posts: 1032
Re: Dynetek DS2-1 Conversion to Bridgestone Points Housing
« Reply #6 on: May 14, 2018, 08:39:53 PM »
The statement was "Dyna requires 3 Ohm or higher resistance coils.  The BS350 coils are roughly 5 Ohms, so they should be fine."  Just to be clear, the 5 ohm coils are OK without any added resistance, although some added resistance would cut down on coil heat and current draw if the spark wasn't adversely affected.

That's a nice clean conversion on your Bridgestone, billdok.
« Last Edit: May 14, 2018, 08:44:23 PM by OldSwartout »
Karl Swartout
Mooresville, IN
BS175 Roadracer
BS350 GTR

Offline SR-175

  • Trade Count: (0)
  • Full Bridgestone Member
  • ***
  • Posts: 67
Re: Dynetek DS2-1 Conversion to Bridgestone Points Housing
« Reply #7 on: May 22, 2018, 01:21:41 PM »
Hi Guys,

I wired the FTR project up as suggested and all went well. It fired up and runs fine. The 350 coils I fitted ran cool while being tested.

Added a few final photos of the project. 

Thanks for the support ... ray 

 


Gallery


Views:15
Comments (1)
By: killerterp

Views:29
Comments (0)
By: rwgibbon

Views:53
Comments (1)
By: fahrkle

Views:82
Comments (1)
By: Geoff S

Classifieds

BS Parts Cabinet & Mics Parts

Price: $0.00
Date: 06/21/2018 07:19 pm
Time Left: 88d 9h 36m
350 GTR/GTO Carbs (Set #2)

Price: $0.00
Date: 06/21/2018 01:29 pm
Time Left: 88d 3h 46m
350 GTR/GTO Wiring Package

Price: $0.00
Date: 06/19/2018 01:33 pm
Time Left: 86d 3h 51m
Wanted BS 100 Sport Fuel Tank and Muffler
Date: 06/14/2018 03:46 pm
Time Left: 81d 6h 3m

Recent Downloads added

Bridgestone Motorcycles

Rating: (None)
Filesize: 3561.91KB
Date: June 05, 2018, 04:42:13 PM
Bridgestone Magazine Article

Rating: (None)
Filesize: 3561.91KB
Date: June 05, 2018, 04:38:08 PM
How to build a 149 mph 350GTR....
Rating: (None)
Filesize: 7154.56KB
Date: April 18, 2017, 08:25:38 AM
Bert Lilley's BS 350 Racer Modifications
Rating: (None)
Filesize: 0KB
Date: January 09, 2017, 04:27:24 PM

Powered by EzPortal